SENGAR ITI
An Industrial Training Institute (ITI) affiliated to the National Council for Vocational Training (NCVT) an advisory body set up by Government of India in 1956.
Syllabus Electrical
SYLLABUS FOR THE TRADE OF ELECTRICIAN
All freshers should undergo one year Basic Training followed by two years training on the Shop Floor. The apprentices should have more practice on the Shop Floor on those operations/skills which have been already learnt during Basic Training.
The content of first year of two years training n the Industrial Training Institutes in this trade is exactly the same as mentioned in (1) above. The trainees of Industrial Training Institutes who may be engaged for two years for Shop Floor Training after one year training in Industrial Training Institute should follow the same course for apprenticeship as in (1) above.
The operations/skills marked (*) would also taught to the trainees in Industrial Training Institutes in this trade in second year. The ex-Industrial Training Institute trainees i.e. those who, after completion of two years training in Industrial Training Institutes, would be engaged for undergoing apprenticeship training FOR the remaining period of one year in this trade, should learn the remaining operations/skills, if any, on the on the Shop Floor during apprenticeship, develop HIS method of work, speed of operations/skills already learnt by him earlier.
SKILL LIST
Instruction in Safety Precautions as applicable to the trade.
2. Use of Fitter’s Hand Tools:
(a) Chipping
(b) Filing
(c) Drilling
(d) Threading
(e) Riveting
(f) Polishing
3. Fitting of bolts, nuts and screws.
4. Grinding of drill bits.
5. Use of carpenter’s basic tools :
(a) Chipping
(b) Planning
(c) Drilling
(d) Chiselling
6. Simple joints in wood.
7. Making distribution box using nails screw etc.
8. Use of power drilling machines.
9. Grinding chisels and screw drivers.
10. Use of electrician’s basic hand tools.
11. Making of joints using single strand cables.
12. Making of joint using multi strand cable.
13. Sweating of conductor with lugs.
14. Soldering joints.
15. Use of switches, plug, sockets etc.
16. Use of cut-out, fuses, regulators, test lamps etc.
17. Making electrical circuits on wooden boards.
18. Use and testing primary and secondary batteries.
19. Use of electrical meters.
20. Verification of Ohm’s Law.
21. Installation of an electrical bell circuits.
22. Installation & testing of light & power, circuits in casing caping, TRS & PVC cables and in conduits.
23. Use of ammeter.
24. *Use of voltmeter.
25. *Use of megger, condenser etc.
26. *Use of wire gauge, tachometer.
27. *Locating & rectifying faults in simple circuits.
28. Use, care, Maintenance and charging of :
(a) Primary cells
(b) Secondary cells.
29. *Running, care and maintenance of :
(a) AC motors and starters-given types.
(b) DC motors and starters-given types.
30. *Repair and testing of domestic and electrical appliances.
31. *Use of different types of wire and cables given types.
32. *Use of distribution and fuse boxes.
33. *Use of various types of switches and fitting-given types.
34. * Use, handling and testing of insulation materials.
35. *Connecting up DC/AC motors and generator to starters field regulators, switch boards.
36. *Making of formas and coils.
37. *Winding of low and medium voltage armatures, fields foils and starters.
38. *Use of growlers.
39. *Soft insulation.
40. *Working to circuit diagrams.
41. *Working to drawings in mm/inch.
42. *Care and maintenance of generators.
43. * Repair and testing of generators.
44. *Installation of light circuits for illumination.
45. *Use of gas discharge & GLS lamps.
46. *Use of intermediate and drum switches 2nd & 3rd year.
47. *Instruction in safety precautions on Shop Floor including first aid and artificial respiration.
48. *Cutting and forming of sheet metal.
49. *Making simple sheet metal articles.
50. *Servicing of domestic & agricultural appliances.
51. *Repair and over-hauling of Ac motors.
52. *Repair and over-hauling of electrical meters.
53. *Rewinding of small power transformer.
54. *Making a buzzer/electric bell/transformer.
55. *Testing & rectifying faults in MG set rotary converter and rectifier.
56. *Concealed wiring.
57. *Earthing.
58. *Industrial switch board work.
59. *Care & maintenance of alternators.
60. *Repair and testing of alternators.
61. *Use, care, testing and routine maintenance of transformers.
62. *Electrical installation and erection of machines.
63. *Care, and maintenance of generators.
64. *Repair and testing of generators.
65. Routine maintenance of electrical machines.
66. Maintenance and minor repairs to electronic controls.
67. *Cable jointing and termination.
68. *Drawing overhead service line.
69. *Bus bar connection.
70. *Simple plumbing work.
Shop Tools, Instruments & Machinery
1. C. Clamps 200 mm, 150 mm, 100 mm 1
2. Spanner 150 mm adjustable 15 degree as cly-burns 2
3. Blow lamp 0.5 liter 2
4. Melting pot 1
5. Ladder 2
6. Chisel cold flat 12 mm X 200 mm 2
7. Chisel wood firmer 25 mm and 6 mm 4
8. Drill machine hand 0 to 6 mm capacity. 2
9. Electric drill machine portable 6 mm capacity 1
10. Pillar electric drill machine 12 mm capacity 1
11. Allen key 1set
12. Oil can 0.12 liter 2
13. Grease gun 1
14. Out side micrometer 0 to 25 mm 1
15. Bench grinder motorised 1
16. Rawl plug tool and bit. 2 set
17. Pull puller 1
18. Bearing puller 1
19. Multi meter 0 to 1000 M Ohms 2.5 to 5000 volt 1
20. Ammeter 1 MA TO 500 MA 1
21. Ammeter 0 to 1 ammp. DC 1
22. K.W. meter 0 to 1 K.W. capacity with C.T. 1:2 1
23. Single phase power factor meter 1
24. Frequency meter 1
25. Tong tester (Clipon meter) 1
26. Mill Voltmeter centre zero 100-0-100 m volt 1
27. Spring balance 0 to 15 kg. and 0 to 2.25 kg. 2 set
28. Stop watch 1
29. Techno-meter or revolution counter with stop watch 1
30. Scissors blade 150 mm 1 set
31. Crimping tool 4
32. Screw driver 100mm 4
33. Chisel cold flat 12 mm 4
34. Mallet hard wood 0.50 kg. 4
35. Hammer exetor type 0.40 kg. with handle 3
36. Hacksaw frame 200 mm. 300 mm adjustable ` 4 (2 each)
37. Square try 150 mm, outside & inside caliper 4
38. Divider 150 mm,outside & inside caliper 3
(each)
39. Pliers flat nose 100 mm 4
40. Pliers Gas round nose 100 mm 4
41. Pliers Gas 150 mm 4
42. Tweezers 100 mm 4
43. Snip straight 150 mm 2
44. Snip bent 150mm 2
45. Spanner D.E.W/W standard set 2
46. Drill hand brace 0 to 100 mm 4
47. Drill S.S. Twist block 3 mm, 5mm 6mm set of 3 4
48. Plane, smoothing cutters, 50 mm 4
49. Gauge, wire imperial 2
50. File flat 200mm 2nd cut. 3
51. File half round 200 mm 2nd cut 4
52. File half round 200mm smooth 4
53. File round 200 mm 2nd cut 4
54. File flat 100 mm 2ndr cut 4
55. File flat 150 mm rough 4
56. File flat 250 mm smooth 4
57. File flat 250 mm rough 4
58. File flat 250 mm bastard 4
59. Rasp, half round 200 bastard 4
60. Iron, soldering 225 grams 125 watt 4
61. Vice hand 50 mm jaw 4
62. Stock and dies conduit 1
63. Ammeter M.C. 0-25 A.D.C.
64. Ammeter M.C. 0-25 A.D.C. 1
65. D.C. energy meter 220 V 5A W/H or A/H type 1
66. A.C. voltmeter M.I. 0-500 V 1
67. A.C. Ammeter M.I. 0-25 A 1
68. A.C. Ammeter M.I. 0-5A 1
69. A.C. Energy meter (single phase 5 amp. 230 V) 1
70. Megger 500 volts 1
71. Wheat stone bridge complete with galvanometer and battery 1
72. Fan A.C. 230 volt 1200 mm 2
73. Fan D.C. 220 volt 1200 mm 2
74. Bath impregnating 1
75. Oven stoving 2
76. Voice, table jaw 100 mm 3
77. Lockers with 3 drawers(Standard size) 2
78. Bench working 2.5 X 1.20 X 0.75 meter 4
79. Almirah 2.5X 1.20 X 0.50 meter 1
80. Instructor’s table 1
81. Instructor’s chair 2
82. Fire extinguisher 2
83. Fire buckets 4
84. Metal rack 180 X 150 X45 cm` 4
85. Wire stripper 20 cm 1
Shop Tools, Instruments & Machinery (Contd..)
86. Copper bit soldering iron 0.25 kg 4
87. Domestic appliances:
(a) Electric hot plate 1500 watt 220 V with temperature control 2
(b) Electric Kettle, 100 watts, 230 V. 2
(c) Electric iron 1200 watts, 230 V with temperature control. 2
(d) Immersion heater 750/1000/1500 W-230 V. 2
(e) Geyser 25 liter 240 V (storage type)
(f) B.A. taps and dies 0-2-4-6-8 sizes 1 set
88. Spring balance 0-1 kg. 1
89. Laboratory type induction coil 6 Volt to 800-10,000 volt 1
90. Series type Ohm meter 0-2000 approximate. 1
91. Shunt type Ohm meter 0-25 approximate 1
92. 3-point D.C. starters 1
93. 4-point D.C. starters 1
94. Pipe cutter to cut pipes up to 5 cm dia 4
95. Pipe cutter to cut pipes up to 5 cm dia 1
96. Cut out, reverse current, over load voltage relays 1
each
97. Stock and die set for 20mm to 5mm G.I. pipe set
98. Starters for 3-phase,400V, 50 cycles, 2 to 5 H.P. A.C. motors 1
(a) Auto transformer type starter
(b) Star delta starter with manual, Semi-auto & Automatic
(c) Direct on line starter.
99. Motor A.C. series type 230 V, 50 cycles,
¼ HP with starter and switch 1
100. Electrical machine trainer Suitable for demonstrating the construction and functioning of different types of DC machines and AC machines (single phase and three phases). Should be complete with friction brake dynamo meter, instrument panel and power supply units 1 per institute
101. Scientific Calculator 2 Nos.
102. Multi meter 2 Nos.
103. Motor generator set consisting of: 1 Motor induction squirrel cage, 7 HP 400 volts, 50-cycles, 3-phase with star delta starter and switch directly coupled to DC shunt Generator 5 KW 440 volts, and switch board mounted with regulator, air circuit breaker, ammeter, voltmeter knife blade switches and fuses, set complete with case Iron and plate, fixing bolts, foundation bolts and flexible coupling.
104. Motor generator set consisting of: 1 Motor shunt 5HP, 440 volts with starting compensator and switch directly coupled to generator A.C. 3.5 KVA, 400/2300 volts, 3-phase, 4 wire, 0.3 PF 50 cycles With exciter and 1 switch board mounted with regulator, knife blade switch and Fuses etc. Set complete with cast iron bed blade. Fixing bolts, foundation bolts, & Flexible coupling.
105. Motor service DC, 220 volts, 0.5 to 2 HP, 0.5 to 2HP. 1
106. Motor shunt DC 220 volts, 2 to 3 HP 2
107. Motor of AC squirrel cage, 3-phase, 400 volts, 50 cycles, 2 to 3 HP with star Delta starter & triple pole iron clad switch fuse. 1
108. Motor DC compound-wound 220 volt 2 to 3 HP with starter & switch 1
109. Motor DC compound-wound, 220 volt 2 to 3 Hp with starter & switch 2
110. Motor AC single phase, 230, volt, 1 HP repulsion type complete with 1 Starter & switch.
111 Motor AC single phase 230 volt, 50cycles series type with starter/switch 1 1 HP. 1
112 Motor AC single phase 230 volt, 50 cycles capacitor type with starter switch 1 1 HP
113. Motor universal 230 volt, 50 cycles with starter/switch 1 HP 1
114 Transformer single phase KVA, 230/115 volts, 50 cycles’ core type, air cooled With tapings for scd. Connection 3
115. Transformer three phase, 5 KVA 400/230 volts, 50 cycles, delta and star, shell Type oil cooled 2
116. Current transformer 2
117. Potential transformer 2
118 Used DC generators-series shunt and compound type for overhauling practice 1 each
119 DC shunt generator, 2.5 KW, 220 v with control panel
120 DC compound generator, 2.5 KW 250 v with control panel including field rheostat, Voltmeter, ammeter and circuit breaker. 1
121. Variable auto transformer 0/250 V, % amps. 2
122 Diesel generator, 5 KVA, with change over switch current circuit breaker, water Cooled with armature, star-delta connections. 1
123 Oscilloscope 1
124 Function Generator 1
125. Oil testing kit 1 no
126 Flux meter 1 no
127 Stepper motor 1 no
128 Earth leakage ckt. breaker 1 no
129. Desoldering gum 4 nos.
130. A.C.B 5 KVA 1 no
131 O.C.B 5 KVA 1 no.
132 M.C.B 5 KVA 1 no
133 V.C.B 5KVA 1 no
134 Thyrister driver 1 H.P. with techogenerator 1 no
135. Voltage Stabilizer manual and automatic 1 no each
Get in Touch with us
Sengar ITI, 01 - Panda Road, Near La Sagesse School, Rau, Indore MP, 453331
Phone No. : (+91) 6232581748 , 7509318002 , 9301897401 E-Mail : admin@sengariti.com